Perform reinforcer: 1 increases concrete resistance to abrasion and minimizes the influence of black rubber wheels. Perform reinforcer: 1 is intended to be used on new as old concrete for hardening of the surface. Perform reinforcer: 1 was used advantageously during the slip process to achieve the shine and hardness/hardening demanded during polishing/grinding of various concrete surfaces.
These advantages have Perform reinforcer: 1:
Ready to use right away. It is easy to apply.
Improves durability and increases abrasion resistance compared to untreated surfaces.
Reduces dust formation from mortar and concrete floors. It doesn't leave a film on the surface.
Make it easier to keep clean. It improves final results when grinding/polishing different concrete surfaces.
Has good penetration capacity. It is water-based = solvent-free and is completely colourless and odourless.
Completely diffusion open.
Perform reinforcer: 1 is part of the Perform Floor-Recond System.
For professional use only. pH about 11.4 in concentrate. Store Frost-free. This product is manufactured in Sweden.
Consumption:
0.5-1.5 kg / 10 m2 / layer. Varies with the porosity of the surface, the denser/harder the less consumption. Take a test to:
Ensure that the desired result or expected appearance is achieved. Keep in mind that one and the same concrete surface often shifts a bit in quality, which means that the consumption can vary on the same surface.
Use:
Used only on concrete surfaces. Etching on glass and more read more on restrictions below. Hardened/old concrete: Surfaces must be undamaged, textured, clean, free from frost, cement skin, surface water, oils, grease, coatings, any loose particles and other possible surface pollution. If in doubt, apply to a test area first. For hardening during grinding/polishing, use recommended methods from your machine supplier, regarding the grinding/polishing step you should treat the concrete surface. The substrate must be prepared by appropriate mechanical preparation methods such as grinding, high pressure cleaner, etc.m. depending on the condition of the surface. In all cases, all dust and loose material as well as oil and grease must be completely removed from all surfaces before applying the product. There may be moisture in the substrate, but not standing water.
Application:
The concrete surface must be clean and free from standing water, dust, dirt, paint and oil, and exceed +5°C.
For dust bonding porous surfaces: Apply an opaque film with a low pressure sprayer – or. pour out, e.g. with a watering can and
distribute with soft brush/broom or preferably with "microfiber" mop. Note! Excess in puddles is smeared. When the surface has dried, the
treatment is repeated. Let harden a few hours in between, the surface is walkable within about 2-4 hours. But wait about 2 days before allowing standing water.
Surface temperature and ambient temperature: must be between 7 °c and 35 °c.
Moisture content of the substrate: Can be applied to damp concrete, without any water penetration. Relative humidity 100% max. Dew point Watch out for
Condensation! The surface and floors that have not hardened must be at least 3°C above the dew point to reduce the risk of condensation or flowering on the floor surface.
Cleaning tools: Clean all tools and all application equipment with lukewarm water immediately after use. Hardened material can only be removed mechanically.
Limitations:
Do not use syringes that have been used to spray silicones or release agents. Do not mix different products. Make sure that the spraying equipment is cleaned thoroughly before use. Perform Reinforcer 1 will increase abrasion resistance compared to untreated concrete or coatings of the same type. Immediately wash off leftover sprayed material from glass, aluminium or high gloss surfaces with water to avoid etching the surfaces. Do not use on substrates that have previously been treated with hardening agents/membranes, these layers must be removed for the silicate to react and work with the concrete. In order to obtain a homogeneous result, no dry stains or "puddles" of material must be left when applied. Finish further where necessary. The results of the substrate come and variance depending on age, cement content, moisture content, porosity and how far the product has penetrated the substrate. Perform Reinforcer 1 does not outweigh poor substrates with low cement content. It is not intended for lightweight or extremely porous surfaces or with worn surfaces. Perform Reinforcer 1 does not hide serious stains or excessive wear. An invisible film is formed that may later give a slightly darker shade. Does not create a structure, but the substrate determines the appearance. Do not pour used liquid back into the original container.
Packaging
Ordered individually.
Minimum order is 1 x 25 kg
EAN code Dunk 25 Liters:
| 7330254001571 |
For the download of safety data sheets and product data sheets click here.